Used 54" x 9.00" Loopco Slitting Line: S-298

Used 54" x 9.00" Loopco Slitting Line: S-298

orCall +1 (336) 597-2370

Description

Very nice, used 54" x 9.00" x 40,000 lb slitting line. Off foundation, in warehouse storage.


Manufacture

 - Loopco

 - new 1974


Strip Width

 - 54" max / 1372mm


Strip Thickness

 - .010 - .250" Mild Steel


Coil Size

 - Entry ID - 20-24"

 - Exit ID - 16, 20, 22" 

 - OD - 72"

 - Weight - 40,000 lbs max


Line Direction: Right to Left


EQUIPMENT:

Entry Coil Car:

- Revolvator

- 40,000# Capacity

- 60" wide Bed

- 72" O.D. Capacity

- (2) - 5" bore hydraulic lift cylinders

- Lift: Approx. 16"

- Self-contained hydraulics

- 3 HP AC motor

- Each axle individually driven by hyd. motors

- Pushbutton control

- Approx. 12" from floor to bottom of "V" cradle

- Removable 5" high riser on bed

- Overall size: 90" L x 64" W x 89" High


Uncoiler:

- 20" - 24" I.D.

- Hydraulic Expansion

- Pumpkin Tooth Mandrel

- 54.5" Face Mandrel

- Powered Holddown Roll w/Rubber Covered Roll

- AC Motor Threading Drive w/Air Clutch

- Sliding Base

- Wichita Water Cooled Brake

- Water Cooler for Brake

- Passline: 40" from Floor to Center of Mandrel

- Overall Size: 150" L x 74" W x 93" High


Entry Unit:

- Threading Table

- Pinch Rolls, 8" Dia. x 56.5" Face Rolls, Idler Type

- Side Guides, Manual Adj.

- Passline: 47"

- Overall Size: 84" L x 50" W x 75" High


-Crop Shear:

- 58" Long Blade

- Hydro-Mechanical Up-cut Type

- 10" Bore Hydraulic Cylinder

- Entry Passline Roll

- Spring Loaded Holddown

- Passline: 49"

- Overall Size: 109" L x 35" W x 81" High


Slitter Heads (2 included):

- Crane Type Removable Heads

- Single Eccentric Arbor Adjustment

- 1 x 9" Dia. x 55" Face Arbors

- 1 x 6" Dia. x 55" Face Arbors

- Entry Side Guides, Manual Adj.

- Entry Passline Rolls, 4" Dia. x 59.75" Long

- 75 HP DC Motor, 500/2000 RPM, 500 V, w/Blower

- 30 HP AC Motor Threading Drive, 1760 RPM, 230/460 V

- Alten Gear Reducer w/1.837:1 Ratio

- Overall Size: 

   - 9" Head: 128" L x 57" W x 81" High, 15,000 Lbs.

   - 6" Head: 122" L x 50" W x 69" High, 10,000 Lbs.

   - Drive: 150" L x 46" W x 47" High, 7,500 Lbs.


(2) Scrap Winders:

- Approx. 25" W x 26" Dia. Scrap Ball Capacity

- Hydraulic Motor Driven

- Self-Contained Hydraulic Power Unit = 15 HP AC Motor, 1760 RPM, 230/460V

- Overall Size: 84" L x 52" W x 49" High (Each Winder)


Pit Cross Over Table:


Tension Stand:

 - Stamco

 - Clam Shell Design 

- Hydraulic Cylinder Open / Close 

- Entry Separator Tooling Bar (Not attached to Frame) 

- Exit Passline Rolls - Rubber Covered 

   - Top Roll - 66" Face x 14" Dia.

   - Bottom Roll - 62" Face x 6" Dia., Driven for Threading by Hyd. Motor

- (2) Sets of New Pressure Boards (Less Felt/Carpet Covering) 

- Air Bag Included

- Machine No. 4461 

- Overall Size: 106" L x 39" W x 53" High


Free Standing Overarm Separator: Deflector Roll, Threading Table to Recoiler


Recoiler:

- 16" Dia. x 58" Face Drum

- 20" Dia. Bolt On Pad

- 22" Dia. x 57" Face Spare Drum

- Hydraulic Clamp and Expansion = 12" Dia. Main Shaft

- Hydraulic Pushoff

- Lufkin (2) Speed Gear Box w/10.6:1 and 31.7:1 Ratios

- 200 HP DC Motor, 500/2000 RPM, 500 V w/Blower

- Air Operated Holding Brake

- Passline: 40" from Floor to Center of Drum

- Overall Size: 180" L x 102" W x 92" High


Hydraulic Power Unit: included


Electrical Panel:

- Eurotherm DC Drive:


Tooling:

 - Miscellaneous tooling included

Manufacture - Loopco - new 1974 Strip Width - 54" max / 1372mm Strip Thickness - .010 - .250" Mild Steel Coil Size - Entry ID - 20-24" - Exit ID - 16, 20, 22" - OD - 72" - Weight - 40,000 lbs max Line Direction: Right to Left Entry Coil Car: - Revolvator - 40,000# Capacity - 60" wide Bed - 72" O.D. Capacity - (2) - 5" bore hydraulic lift cylinders - Lift: Approx. 16" - Self-contained hydraulics - 3 HP AC motor - Each axle individually driven by hyd. motors - Pushbutton control - Approx. 12" from floor to bottom of "V" cradle - Removable 5" high riser on bed - Overall size: 90" L x 64" W x 89" High Uncoiler: - 20" - 24" I.D. - Hydraulic Expansion - Pumpkin Tooth Mandrel - 54.5" Face Mandrel - Powered Holddown Roll w/Rubber Covered Roll - AC Motor Threading Drive w/Air Clutch - Sliding Base - Wichita Water Cooled Brake - Water Cooler for Brake - Passline: 40" from Floor to Center of Mandrel - Overall Size: 150" L x 74" W x 93" High Entry Unit: - Threading Table - Pinch Rolls, 8" Dia. x 56.5" Face Rolls, Idler Type - Side Guides, Manual Adj. - Passline: 47" - Overall Size: 84" L x 50" W x 75" High -Crop Shear: - 58" Long Blade - Hydro-Mechanical Up-cut Type - 10" Bore Hydraulic Cylinder - Entry Passline Roll - Spring Loaded Holddown - Passline: 49" - Overall Size: 109" L x 35" W x 81" High Slitter Heads (2 included): - Crane Type Removable Heads - Single Eccentric Arbor Adjustment - 1 x 9" Dia. x 55" Face Arbors - 1 x 6" Dia. x 55" Face Arbors - Entry Side Guides, Manual Adj. - Entry Passline Rolls, 4" Dia. x 59.75" Long - 75 HP DC Motor, 500/2000 RPM, 500 V, w/Blower - 30 HP AC Motor Threading Drive, 1760 RPM, 230/460 V - Alten Gear Reducer w/1.837:1 Ratio - Overall Size: - 9" Head: 128" L x 57" W x 81" High, 15,000 Lbs. - 6" Head: 122" L x 50" W x 69" High, 10,000 Lbs. - Drive: 150" L x 46" W x 47" High, 7,500 Lbs. (2) Scrap Winders: - Approx. 25" W x 26" Dia. Scrap Ball Capacity - Hydraulic Motor Driven - Self-Contained Hydraulic Power Unit = 15 HP AC Motor, 1760 RPM, 230/460V - Overall Size: 84" L x 52" W x 49" High (Each Winder) Pit Cross Over Table: Tension Stand: - Stamco - Clam Shell Design - Hydraulic Cylinder Open / Close - Entry Separator Tooling Bar (Not attached to Frame) - Exit Passline Rolls - Rubber Covered - Top Roll - 66" Face x 14" Dia. - Bottom Roll - 62" Face x 6" Dia., Driven for Threading by Hyd. Motor - (2) Sets of New Pressure Boards (Less Felt/Carpet Covering) - Air Bag Included - Machine No. 4461 - Overall Size: 106" L x 39" W x 53" High Free Standing Overarm Separator: Deflector Roll, Threading Table to Recoiler Recoiler: - 16" Dia. x 58" Face Drum - 20" Dia. Bolt On Pad - 22" Dia. x 57" Face Spare Drum - Hydraulic Clamp and Expansion = 12" Dia. Main Shaft - Hydraulic Pushoff - Lufkin (2) Speed Gear Box w/10.6:1 and 31.7:1 Ratios - 200 HP DC Motor, 500/2000 RPM, 500 V w/Blower - Air Operated Holding Brake - Passline: 40" from Floor to Center of Drum - Overall Size: 180" L x 102" W x 92" High Hydraulic Power Unit: included Electrical Panel: - Eurotherm DC Drive: Tooling: - Miscellaneous tooling included

Specifications

ManufacturerLOOPCO
Model54" Slitting Line
Year1974
ConditionUsed
Stock NumberS-298
TypeSlitting, Slitting Lines
StatusFor Sale
Line DirectionRight to Left
Free Standing Overarm SeparatorDeflector Roll, Threading Table to Recoiler
Hydraulic Power Unitincluded
Tooling- Miscellaneous tooling included