Two (2) Used 74" (1880mm) Twin-Roll Continuous Aluminum Strip Casting Lines: MC-465

FOR SALE !!! - TWO (2) 74" ALUMINUM STRIP CASTING LINES: MC-465

Two Complete lines but the Owner will not sell one set of furnaces.

Manufacturer
- Zhuoshen / Solios / Novelis / Alpur
- New 2008

Material
- Aluminum alloys 1xxx, 3003, 8011

Strip Width
- 1880mm max (74")
- 1850mm after edge trimming (72.83")
- Roll faces = 2100mm (82.68")

Strip Thickness
- 6.0mm nominal (.236")
- 4.0 - 8.0mm design capacity (.157 - .315")

Coil Size
- ID = 610mm (24")
- OD = 2150mm (84.65")
- Weight = 16,000kg (35,274lbs)

Pass Line Height:
- 1000mm +/-

Status:
- Very little use / installed / complete / ready to inspect
- Line A never ran production
- Line B ran on and off

EQUIPMENT
Melting Furnaces:
- 1 furnace for sale
- 37 mton reverb type
- 2 burners = 1 Pair of Regenerative Burners (4343-12B - 7000kW)
- Burners were upgraded to Natural gas in Q1 2017

Holding Furnaces:
- 1 furnaces for sale
- 37 mton stationary tilting furnace
- 2 burners = 1 x Nox Beta 2400C (1500kW) + 1 x Nox Beta 600C (500kW)
- Burners were upgraded to Natural gas in Q1 2017

Molten Metal Troughs:
- Included

Grain Refiner Rod Feeder:
- 1.5 kW, 8-12mm diam rod, 400kg max rod coil

Degasser:
- Alpur

Filtration:
- Novelis
- Ceramic Foam Filter (plus one spare unit)

Molten Metal Level Control:
- Included

Graphite Spray Systems:
- 1.5 kW AC motor, 2000mm stroke,

Casters (Zhuoshen):
- Screw-down cylinders: 680mm cylinder diam / 560mm rod diam x 115mm stroke / working pressure of the chamber without rod = Max. 32 MPa / Rolling force max 23,000 KN
- Tip Table
- Max. rolling force = 23,000 KN
- Caster housings size = 360mm × 490mm
- Max. torque of single roll = 600 KN.m
- Caster drive motor = 2 × 81kW x 0/900/2000rpm x 400VDC x thru 760:1 gearbox
- Both rolls are driven
- Rolling Speed = 4000mm/min
- Roll change = hydraulic on rails

Caster Rolls:
- Roll Diameter: 1020mm new (39.84")
- 9 sets / 18 rolls (count must be confirmed)
- It is thought that all rolls are closers to their minimum diameters
- Roll Shells: material 32Cr3Mo1V / hardness HB380～420 / new wall thickness = 80mm / Min wall thickness = 25mm
- Roll Cores: material 42CrMo / core diam 860mm / surface = 16mm stainless steel / water supply & return = three in and three out
- Bearings: 4 rows of cone roller bearings
- Chock material: ZG270-500

Runout Zone:
- Guide roll

Edge Trimmer:

Gauge Control:
- inline strip thickness and flatness measurements

Pinch Roll:
- 8 mtons of tension max, 300mm roll diam

Shear:
- hydraulic, 360KN, 6 cuts/min

Deflector Roll:

Recoiler:
- Drive motor - 22kW, 0/500/1760rpm, 400 VDC
- Max Coiling Tension - 210KN
- Mandrel = hydraulic expansion (570-610mm), 2000mm face, Strip infeed slot
- Entry support plate and 350mm guide roll diam
- Hydraulic push off plate

Coil Car:
- In-ground, on rails, 960mm lift stroke

Complete hydraulic systems, electrics, controls, etc.

Spares:
- Many Spares are included
- Please ask for our excel sheet that details 101 lines of spares

Sold "as is, where is" EXW installed on foundation, not under power.